Kit boxes

Cross section diameter gauges moulded into the o-ring kit box itself, are accurately calibrated cross section slots. These slots assure precision measurement of o-rings to be replaced.

BOXH Metric o-rings
NBR 70° Shore A
30 sizes = 404 pcs. 18 pcs 3 x 2 18 pcs 4 x 2 18 pcs 5 x 2 18 pcs 6 x 2 17 pcs 7 x 2 17 pcs 8 x 2 17 pcs 10 x 2 14 pcs 10 x 2.5 14 pcs 11 x 2.5 14 pcs 12 x 2.5 14 pcs 14 x 2.5 14 pcs 16 x 2.5 14 pcs 17 x 2.5 14 pcs 19 x 2.5 12 pcs 19 x 3 12 pcs 20 x 3 12 pcs 22 x 3 12 pcs 24 x 3 12 pcs 25 x 3 12 pcs 27 x 3 12 pcs 28 x 3 12 pcs 30 x 3 12 pcs 32 x 3 12 pcs 33 x 3 12 pcs 35 x 3 12 pcs 36 x 3 12 pcs 38 x 3 9 pcs 38 x 4 9 pcs 42 x 4 9 pcs 45 x 4

BOXG Imperial o-rings
NBR 70° Shore A
30 sizes = 382 pcs BS 006 20 pcs 2.9 x 1.78 BS 007 20 pcs 3.68 x 1.78 BS 008 20 pcs 4.48 x 1.78 BS 009 20 pcs 5.28 x 1.78 BS 010 20 pcs 6.07 x 1.78 BS 011 20 pcs 7.66 x 1.78 BS 012 20 pcs 9.25 x 1.78 BS 110 13 pcs 9.19 x 2.62 BS 111 13 pcs 10.78 x 2.62 BS 112 13 pcs 12.31 x 2.62 BS 113 13 pcs 13.95 x 2.62 BS 114 13 pcs 15.54 x 2.62 BS 115 13 pcs 17.13 x 2.62 BS 116 13 pcs 18.72 x 2.62 BS 210 10 pcs 18.64 x 3.53 BS 211 10 pcs 20.22 x 3.53 BS 212 10 pcs 21.82 x 3.53 BS 213 10 pcs 23.40 x 3.53 BS 214 10 pcs 24.99 x 3.53 BS 215 10 pcs 26.58 x 3.53 BS 216 10 pcs 28.17 x 3.53 BS 217 10 pcs 29.75 x 3.53 BS 218 10 pcs 31.34 x 3.53 BS 219 10 pcs 32.92 x 3.53 BS 220 10 pcs 34.52 x 3.53 BS 221 10 pcs 36.10 x 3.53
BS 222 10 pcs 37.69 x 3.53
BS 325 7 pcs 37.47 x 5.33
BS 326 7 pcs 40.65 x 5.33
BS 327 7 pcs 43.82 x 5.33

Splicing Kit

HOW TO MAKE AN O-RING To calculate the correct length of cord required, multiply the inside diameter of the o-ring by pi, then add 1x cord diameter. This will then give the correct length of cord required. Using the splicing aid and a very sharp knife. make a cut in the material at a right angle. All surfaces to be glued must be free of oil or grease. Avoid touching the surfaces. A thin layer of glue should be spread over one side of the cut. A thin layer provides the best results. In order to join the two sides cleanly, use the V section on the splicing aid. Match both surfaces together and press firmly for 15 seconds. The glue must dry for 60 seconds before mounting the O-ring
Kits available: (see contents list) Kit S - 11 size Splicing Kit Kit SL - 16 Size Splicing Kit	Contents List SPLICING KIT ll size 2M C0178 1/16 nom C0262 3/32 nom C0350 1/8 nom C0533 3/16 nom C0699 1/4 nom 2M CO160 1.6mm C0200 2.0mm C0300 3.0mm C0400 4.0mm C0500 5.0mm C0570 5.7mm TOOL BOX KNIFE LF600 (5g glue) BLOCK + these for the 16 size kit 2m CO150 1.5mm C0240 2.4mm C0250 2.5mm C0350 3.5mm C0840 8.4mm
Copper Sealing Washer Kit
Kits available: AB32 - Copper Washer Kit (up to 1" BSP) AB92 - Metric Copper Washer Kit

Kit Boxes - page 1

O-Rings

Contents List:

Splicing Kit